Cyclades AlterPath BladeManager Manual de instrucciones Pagina 84
- Pagina / 240
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
70 MergePoint 5224/5240 Service Processor Manager Installer and Administrator Guide
To configure the AUX port for IPDU power management:
This procedure assumes that a Cyclades PM IPDU is connected to the AUX port.
1. Select the Settings
- AUX Port menu option.
2. Make sure the Power Management option is selected from the Profile menu.
3. (Optional) Enter a name for the connected IPDU in the Name field.
4. Click Save and apply changes.
5. Go to Configuring IPDU Power Management on page 70.
To configure an AUX port for modem access:
1. Select the Settings
- AUX Port menu option.
2. Select Modem from the Profile menu.
3. Choose Login, Autodetect, PPP or OTP from the Modem access menu.
4. Select a baud rate from the Baud Rate pull
-down menu.
5. If you chose either Login or Autodetect, select an option from the Flow Control menu.
6. Enter a modem chat string in the Modem Initialization field.
7. If you chose PPP or Autodetect, perform the following steps:
a. Enter a local IP address or accept the default provided in the Local IP address field.
b. Enter a remote IP address or accept the default provided in the Remote IP address field.
c. Enable or disable authentication by checking or leaving unchecked the Authenticating
Required checkbox.
d. Accept or change the value in the MTU field.
e. Accept or change the value in the MRU field.
f. Accept or change PPP options as desired in the PPP Options field.
8. Enable callback, if desired, by performing the following steps.
a. Check the Use Callback checkbox. The Callback Number field appears.
b. Enter a callback phone number.
9. Click Save and apply changes.
Configuring IPDU Power Management
When an administrative user clicks the IPDU option under Settings, three tabs appear for
configuring connected IPDU(s).
The first IPDU connected to the AUX port is called the Master Unit. An additional IPDU that is
daisy
-chained to the first IPDU is called a Slave Unit.
The IPDU power management configuration procedures assume that the user account has been
defined as described under To create and authorize a user for device management (Wizard): on
page 66.
- MergePoint™ 1
- 5224/5240 1
- USA Notification 2
- Canadian Notification 2
- MergePoint™ 5224/5240 3
- Service Processor Manager 3
- Table of Contents 5
- Table of Contents v 7
- List of Figures 11
- List of Tables 13
- Installation Introduction 15
- MERGEPOINT 16
- Modem Types and Options 18
- Power Management Unit Options 18
- -tilt bar 19
- Basic Installation Procedures 21
- Connecting Devices 24
- Advanced Installation Topics 31
- Telephone 32
- Administration Introduction 35
- SP Manager 38
- User and Group Configuration 39
- Security Profiles 39
- Services 41
- Telnet service configuration 42
- Telnet client configuration 42
- DHCP client 42
- DHCP server 43
- IPSec VPN connections 48
- PPTP VPN connections 50
- Manager 52
- Syslog servers 53
- Private Ethernet ports 53
- Public Ethernet ports 53
- Failover 53
- Ethernet media configuration 54
- Dial-in and Callback Access 55
- Power Management Options 57
- Target Device Configuration 59
- 5224/5240 SP Manager 64
- -in chains 69
- Using the Web Manager 71
- Dialogs in the Web Manager 73
- Web Manager Wizard 74
- Configuring routes 76
- Configuring failover 76
- Upgrading IPDU Software 82
- Configuring the AUX Port 83
- - AUX Port menu option 84
- Configuring PC Cards 86
- -down menu on the PCMCIA 88
- -down menu on the 88
- - Date/time menu option 88
- Local boot options 89
- Network boot options 90
- Configuring Outbound Email 91
- # gunzip 92
- Configuring Target Devices 93
- Configuring Users and Groups 95
- Configuring Device Groups 97
- - Authentication menu option 100
- -down menu 100
- 5240 SP Manager 104
- Configuring Notifications 104
- - Notifications menu option 105
- -down menu. If the 105
- Configuring Sensor Alarms 107
- Configuring SNMP 110
- - SNMP menu option 113
- - Host settings menu option 115
- Configuring Hosts 117
- Configuring Static Routes 118
- Configuring VPN Connections 118
- Viewing System Information 121
- - Product upgrades 123
- - Restart menu option 124
- Administration Tasks Not 125
- Performed in the Web Manager 125
- -mounted directory 128
- -t ext2 /dev/hdc1 /mnt/opie/) 128
- -in or Telnet connection: 131
- Configuring the DHCP Server 134
- -q priv0" 136
- -ins Using cli 136
- -flow type to both 137
- -flow both 137
- Configuring Routes With cli 141
- Saving Configuration Changes 142
- saveconf 143
- MergePoint5224 login: root 145
- Password: password 145
- -out] [retries] 150
- Using the cli Utility 157
- Interactive mode 158
- Batch mode 158
- Autocompletion 162
- Enter> 163
- Parameters that can be added 165
- -source <IPaddress>] 174
- Default: no setting 178
- Appendices 179
- Login failure 180
- Web manager stops responding 181
- Firmware image is corrupted 181
- Target device types 183
- Appendices 171 185
- Appendices 173 187
- Using the sptemplate utility 188
- Appendices 179 193
- Appendices 181 195
- Why define private subnets? 196
- Configuring a private subnet 197
- Appendices 189 203
- Appendices 191 205
- Appendices 193 207
- IP: 192.168.4.22 208
- Appendices 195 209
- Appendices 199 213
- Boot file location 214
- Changing the boot image 216
- <N> completed 219
- Appendix E: Technical Support 222
- Numerics 223
- Index 211 225
- Index 213 227
- Index 215 229
- Index 217 231
- Index 219 233
- Index 221 235
- Index 223 237
Relacionado con productos y manuales para Servidores Cyclades AlterPath BladeManager
(202 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales