Cyclades AlterPath BladeManager Manual de instrucciones Pagina 27
- Pagina / 240
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2: Basic Installation Procedures 13
Connecting a Terminal to Configure Basic Network Parameters
If you connect a terminal or workstation to the console port, you can use the cli utility to configure
basic network parameters as described in To configure basic network parameters using a terminal:
on page 14.
Perform the following steps to connect a terminal or a workstation to the console port. If
connecting a PC, make sure that HyperTerminal or another terminal emulation program is installed
on the Windows operating system. On a workstation running a UNIX
-based operating system, such
as Linux or Solaris, make sure that a compatible terminal emulator such as Kermit or Minicom
is installed.
This procedure assumes you have the RJ
-45 to DB-9 6 ft CAT 5 cable shipped with the SP manager
or an off
-the-shelf equivalent CAT 5 or greater cable. If the terminal or workstation has a USB port,
you also need a USB to DB
-9 converter.
NOTE: Only use a crossover cable.
To connect a terminal to the console port:
1. If connecting to a workstation or terminal with a DB
-9 male port, perform these steps.
a. Connect the RJ
-45 end of the cable to the console port.
b. Connect the DB
-9 male end of the cable to the DB-9 connection on the terminal
or workstation.
2. If connecting to a workstation or terminal with a USB port, perform these steps.
a. Connect the RJ
-45 end of the cable to the console port.
b. Connect the DB
-9 female end to the DB-9 male end of a USB converter.
c. Connect the USB end of the converter to a terminal or workstation.
Enabling Access to the Web Manager
Perform the procedures in this section to enable a remote administrator to finish configuration
using the Web Manager. These procedures require a terminal or a computer with a terminal
emulation program to be physically connected to the console port of the SP manager.
Use the default IP address
192.168.160.10 to bring up a Web
Manager to set a fixed
IP address.
You must temporarily change the network portion
of the IP address of a computer on the same
subnetwork to be able to use the default IP
address in launching the Web Manager.
To use a dynamic IP
address to access the
Web Manager: on
page 14
Table 2.1: Methods for Enabling Web Manager Access (Continued)
Method Considerations Where Described
- MergePoint™ 1
- 5224/5240 1
- USA Notification 2
- Canadian Notification 2
- MergePoint™ 5224/5240 3
- Service Processor Manager 3
- Table of Contents 5
- Table of Contents v 7
- List of Figures 11
- List of Tables 13
- Installation Introduction 15
- MERGEPOINT 16
- Modem Types and Options 18
- Power Management Unit Options 18
- -tilt bar 19
- Basic Installation Procedures 21
- Connecting Devices 24
- Advanced Installation Topics 31
- Telephone 32
- Administration Introduction 35
- SP Manager 38
- User and Group Configuration 39
- Security Profiles 39
- Services 41
- Telnet service configuration 42
- Telnet client configuration 42
- DHCP client 42
- DHCP server 43
- IPSec VPN connections 48
- PPTP VPN connections 50
- Manager 52
- Syslog servers 53
- Private Ethernet ports 53
- Public Ethernet ports 53
- Failover 53
- Ethernet media configuration 54
- Dial-in and Callback Access 55
- Power Management Options 57
- Target Device Configuration 59
- 5224/5240 SP Manager 64
- -in chains 69
- Using the Web Manager 71
- Dialogs in the Web Manager 73
- Web Manager Wizard 74
- Configuring routes 76
- Configuring failover 76
- Upgrading IPDU Software 82
- Configuring the AUX Port 83
- - AUX Port menu option 84
- Configuring PC Cards 86
- -down menu on the PCMCIA 88
- -down menu on the 88
- - Date/time menu option 88
- Local boot options 89
- Network boot options 90
- Configuring Outbound Email 91
- # gunzip 92
- Configuring Target Devices 93
- Configuring Users and Groups 95
- Configuring Device Groups 97
- - Authentication menu option 100
- -down menu 100
- 5240 SP Manager 104
- Configuring Notifications 104
- - Notifications menu option 105
- -down menu. If the 105
- Configuring Sensor Alarms 107
- Configuring SNMP 110
- - SNMP menu option 113
- - Host settings menu option 115
- Configuring Hosts 117
- Configuring Static Routes 118
- Configuring VPN Connections 118
- Viewing System Information 121
- - Product upgrades 123
- - Restart menu option 124
- Administration Tasks Not 125
- Performed in the Web Manager 125
- -mounted directory 128
- -t ext2 /dev/hdc1 /mnt/opie/) 128
- -in or Telnet connection: 131
- Configuring the DHCP Server 134
- -q priv0" 136
- -ins Using cli 136
- -flow type to both 137
- -flow both 137
- Configuring Routes With cli 141
- Saving Configuration Changes 142
- saveconf 143
- MergePoint5224 login: root 145
- Password: password 145
- -out] [retries] 150
- Using the cli Utility 157
- Interactive mode 158
- Batch mode 158
- Autocompletion 162
- Enter> 163
- Parameters that can be added 165
- -source <IPaddress>] 174
- Default: no setting 178
- Appendices 179
- Login failure 180
- Web manager stops responding 181
- Firmware image is corrupted 181
- Target device types 183
- Appendices 171 185
- Appendices 173 187
- Using the sptemplate utility 188
- Appendices 179 193
- Appendices 181 195
- Why define private subnets? 196
- Configuring a private subnet 197
- Appendices 189 203
- Appendices 191 205
- Appendices 193 207
- IP: 192.168.4.22 208
- Appendices 195 209
- Appendices 199 213
- Boot file location 214
- Changing the boot image 216
- <N> completed 219
- Appendix E: Technical Support 222
- Numerics 223
- Index 211 225
- Index 213 227
- Index 215 229
- Index 217 231
- Index 219 233
- Index 221 235
- Index 223 237
Relacionado con productos y manuales para Servidores Cyclades AlterPath BladeManager
(202 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales